Saeed Arabha | Research Profile

Materials R&D · Process Development

PhD in Mechanical Engineering · Toronto, ON

Download résumé

Materials process development and characterization

I develop lab-scale processes for 2D materials and use spectroscopy, microscopy, and molecular simulation to understand how processing affects the material.

Process development

At York, I rebuilt a gas-driven exfoliation apparatus. In a three-pass experiment, I recovered 316 mg of graphene from 1 g of graphite by reprocessing the sediment between passes.

31.6% cumulative recovery

See the apparatus

Surface characterization

I compared the surface chemistry of reference MoS₂ and samples processed in air and helium. I wrote a Python workflow to fit overlapping XPS peaks.

Fitted MoS₂ XPS spectra
Reference, helium, and air from left to right. The dominant Mo–S peaks persisted after processing.
See the XPS analysis

Automated deposition of 2D materials

I built a setup for liquid–liquid interface deposition on wafer substrates. It uses a motor to lift the sample and a syringe to feed liquid through a repeatable deposition sequence.

Methods in practice

Choosing a centrifugation speed for MoS₂

Increasing centrifugation speed from 1,500 to 4,500 rpm reduced the recovered concentration from 1.65 to 0.49 g/L. The estimated mean flake size fell from 286 to 132 nm. Higher speeds gave smaller flakes at the cost of recovered concentration.

Characterization methods

XPS peak fitting in Python

I compared X-ray photoelectron spectra from reference samples and materials processed in air and helium. My Python workflow applied energy referencing and Shirley background subtraction, constrained overlapping peaks such as S 2s and Mo 3d, and exported fitted component areas for comparison.

Materials characterization

Modeling graphene layer separation

I led a study comparing sliding, edge peeling and pulling graphene sheets straight apart. Using steered molecular dynamics and potential-of-mean-force analysis, I found lower separation resistance for sliding and peeling in the simulated configurations.

First-author paper

Graphene recovery across three passes

Doubling the collection volume roughly halved the measured concentration, so I compared recovered mass as well. Starting with 1 g of graphite, I recovered and reprocessed the sediment between passes. The three compressed-air passes recovered 316 mg of graphene in total (31.6% of the original feed).

R&D portfolio

Boron nitride process development

In my doctoral work, I tested how gas preheating and operating conditions affected the concentration of boron nitride recovered after exfoliation. Across the nitrogen-based conditions tested, the combined operating changes raised the recovered concentration from about 0.003 to 0.155 g/L. I calibrated the UV–vis measurements for each material by drying and weighing known volumes of suspension.

Thesis measurements

Shock-tube experiments

I contributed to the experimental investigation and validation of boron nitride exfoliation. At 1.4 MPa driver pressure, our team measured nearly four times the UV–vis absorbance at 350 nm with the tube open at the end compared with the closed configuration.

Peer-reviewed study

Research interests

2D Nanomaterials, Multiscale Modeling, Heat Transfer, Statistical Mechanics

Education

PhD in Mechanical Engineering

York University, Toronto, Ontario, Canada · 2021 – 2026

Compressible Flow Exfoliation of 2D Nanomaterials

Master of Science in Mechanical Engineering, Energy Conversion

IK International University, Qazvin, Iran

Bachelor of Science in Mechanical Engineering

IK International University, Qazvin, Iran · 2013 – 2017

Tools and techniques

Characterization and analysis

Raman Spectroscopy · Scanning Electron Microscopy · Atomic Force Microscopy · FTIR · XPS · Python · MATLAB

mIRage-Raman Main Operator Certification · January 2026

Simulation

LAMMPS · GROMACS · COMSOL · Ansys Fluent

Mechanical design

SolidWorks · Catia

Research and development

Materials, process development, and metrology portfolio Measurements and original thesis results Research commercialization and customer discovery

Teaching experience

  • Teaching Assistant in Dynamics, Simulation Tools for Design & Analysis, and Machine Elements Design, Mechanical Engineering Department, York University, Toronto, ON, Canada.
  • Researcher in Advanced Simulation and Computing Lab, Mechanical Engineering Department, IK International University, September 2015 – 2021.
  • Teaching Assistant in Fluid Mechanics І, Mechanical Engineering Department, IK International University, Autumn 2017, Qazvin, Iran.
  • Teaching Assistant in Heat Transfer, CFD, Thermodynamics, Mechanical and Electrical Engineering Department, IK International University, Spring 2017 – 2018, Qazvin, Iran.
  • Internship in TAHVIE Co, Air Conditioning Systems, Technical Office, Summer 2015, Qazvin, Iran.

Awards

  • Lab2Market Validate (Mitacs Award, $1,000), "Scalable and Green Nano-manufacturing of Graphene and 2D Nanomaterials for Energy and Consumer Technologies," 2025.
  • Mitacs Globalink Research Award ($6,000), Visiting Researcher, Universität Kassel, Germany, 2025.
  • Ranked 1st Among the BS Mechanical Engineering Alumni”, IK International University.
  • Visiting the 'Condensed Matter and Statistical Physics of the Abdus Salam International Centre for Theoretical Physics (ICTP)' and collaboration with E. Roldan and A. Hassanali on a research project on 'inverse heat flux between nanoparticles', from 21 October to 18 November 2019, Trieste, Italy.

Conference presentations

  • "Optimizing Hexagonal Boron Nitride (h-BN) Production via Compressible Flow Exfoliation (CFE)" · Oral Presentation · the E-MRS 2025 Spring Meeting, Strasbourg, France · May 2025
  • "Compressible Flow Exfoliation of Graphene: A Multiscale Study" · Oral Presentation · (CSME) Congress, Université de Sherbrooke, Canada · 2023
  • "Operation of Conventional Treatment Processes" · Workshop Attendee · Walkerton Clean Water Centre, ON, Canada · July 2023
  • "Molecular Dynamics and its Applications to Biological Systems" · Workshop Attendee · ICTP, Trieste, Italy · September 2020
  • "Joint QLS-CMSP Virtual Summer Retreat on Heat, Water, Noise, and Life" · Virtual Seminar · ICTP, Trieste, Italy · Jul 2020
  • "1st conference on computation of nanostructures" and "Quantum calculation using Quantum Espresso” · Oral Presentation · Sharif university of Technology, Tehran, Iran · July 2018
  • "A Not-so-brief Introduction to Molecular Biophysics" · Crash Course · Institute for Research in Fundamental Sciences (IPM), Tehran, Iran · April 2019
  • "26th IPM Physics Spring Conference" · Oral Presentation · Institute for Research in Fundamental Sciences (IPM), Tehran, Iran · June 2019
  • 7th National Conference on Nano technology from theory to application · Oral Presentation · Jami Institute of Technology, Tehran, Iran · June 2019
  • "1st national conference on Micro/Nano scale technologies" · Oral Presentation · IK International University, Qazvin, Iran · May 2018

Publications

Selected papers

  • Graphene separation energetics

    ACS Applied Nano Materials · 2026

    I led the molecular simulation study and compared the energy required to separate graphene layers by sliding, peeling, and pulling them apart.

  • Gas dynamics of exfoliation

    Advanced Engineering Materials · 2026

    I contributed continuum flow analysis and helped interpret how gas acceleration and drag affect layer separation.

  • Porous borophene

    Composites Part B: Engineering · 2020

    I developed software and modeling methods to study how pore geometry affects directional heat transport and mechanical properties.

Full publication list

Publication archive